GrimmerSchmidt

GrimmerSchmidt's 185E MonoBlock compressor features electronic fuel injection, timing and ignition, and is designed to start in cold weather without using starting aids, down to negative 20 degrees. Weighing in at 1,500 pounds without options, the 185E features a high visibility safety yellow, no-rust plastic hood. Other features include a combination ball/pintle hitch, a separate lockable tool storage area, and stop tail and turn lights.
Circle 152 on Reply Card ▪ freeproductinfo.net/rer

CS Unitec

CS Unitec's portable pneumatic hacksaw is designed with the power and durability to stand up to demanding cutting applications, such as onsite cold cutting of pipe, structural steel or tanks, including pipe repair and demolition applications. The hacksaw has a stroke of 2 3/8-inches and zero to 350 strokes per minute. It will cut 24-inch diameter pipe in one pass and can be used manually or with an automatic feed device. The hacksaw is particularly useful for working in confined spaces, and because it is air powered, it is safer for use in hazardous environments. It can be attached to an accessory clamp to allow 90-degree cuts.
Circle 153 on Reply Card ▪ freeproductinfo.net/rer

Porta-Nails

Porta-Nails' new Portamatic Hammerhead TL and S nailers are designed for users who need speed and dependability. The TL Model 470 is a hammer-actuated pneumatic nailer, designed for nailing ½-inch and ¾-inch tongue and groove wood flooring. The TL Model 470 offers a magazine that can hold up to 150 nails and can accommodate either T or L Porta-Nails, which come in a variety of lengths to accommodate specific application needs. The S Model 472 is a hammer-actuated stapler that fires a 15-gauge ½-crown staple. The stapler holds up to 150 staples and is designed for nailing ½-inch and ¾-inch tongue and groove wood flooring. Both models will seat nails at 75 to 90 psi.
Circle 154 on Reply Card ▪ freeproductinfo.net/rer

Ingersoll Rand

Ingersoll Rand's 3900Ti Series of titanium industrial impact tools are designed for heavy use in nearly any impact application. The titanium impacts weigh between 21 and 23 pounds and offer maximum forward torque from 500 to 2,750 foot-pounds, with 500 to 3,250 foot-pounds of torque in reverse. The engines offer improved airflow with a 75- to 95-cfm output range. The titanium hammer casing and reverse-biased brass endplates increase strength and provide corrosion resistance. Other key features of the series include reduced vibration and noise levels, laser-etched product information and ergonomic handles.
Circle 155 on Reply Card ▪ freeproductinfo.net/rer

Kaeser Compressors

Kaeser Compressors' complete line of MobilairTools includes heavy-duty clay and trench diggers. The tools are built to be rugged and dependable for clearing dirt from existing foundations, as well as laying pipe or cables, and are specifically made to dig clay, shale or frozen ground. Tool steel selections for both clay and trench diggers include points and chisels in different widths, as well as clay spades and scoops. A standard D-style handle with inside trigger offers better control and improves safety.
Circle 156 on Reply Card ▪ freeproductinfo.net/rer

Atlas Copco

Atlas Copco Construction Tools offers the TEX P60 and TEX P90 (pictured) pneumatic hand-held breakers. Constructed with fewer moving parts for reliability and productivity, the breakers are built for breaking asphalt and concrete. Weighing 68 and 88 pounds, respectively, the TEX P60 and TEX P90 feature a SOFSTART two-step trigger that gives the operator better control of the chisel. Breaking accuracy is improved by a long piston head that allows better guidance in the cylinder. Requiring between 76 and 85 cfm of free air delivery at 92 psi, the TEX breakers produce between 1,260 and 1,500 blowers per minute. The breakers' high power-to-weight ratio and low center of gravity allow for easy handling and good operator balance, reducing operator fatigue.
Circle 157 on Reply Card ▪ freeproductinfo.net/rer

General Equipment

General Equipment's MDF15 long-reach air tool is designed for asbestos abatement, coating and acoustic tile removal, as well as a wide variety of surface cleaning and preparation applications. Weighing less than 10 pounds without additional accessory tools, the MDF15's lightweight aluminum construction works for above waist and overhead projects. Producing 3,700 blows per minute while requiring a flow rate of 6 cfm at 90 psi, the MDF15 is easy to use while being effective. The MDF15 is available with a variety of standard accessory tools and also includes an ergonomically designed throttle valve with protective enclosure and a 60-inch whip hose.
Circle 158 on Reply Card ▪ freeproductinfo.net/rer

Edco

Edco's CD-3 scabbler removes 1/8-inch to 3/16-inch of concrete per pass. Long-lasting, high-quality tungsten carbide bits are designed to increase production rates and lower operating costs. Standard features include a Whipchek safety cable and an inline oiler to reduce maintenance and increase machine life. The CD-3 scabbler requires 100 cfm of compressed air and is equipped with a 2-inch vacuum port to provide dust-free operation.
Circle 159 on Reply Card ▪ freeproductinfo.net/rer

Kent Demolition

Kent's Redline Series of pneumatic hand tools includes breakers, rivet busters, clay diggers, trenchers, chippers, tampers, sump pumps and rock drills. The tools feature drop-forged construction and four-bolt, ergonomically designed handles for operator comfort and rigid connection to the cylinder. Teflon/graphite packing provides cooler operation, seals out dirt and needs no adjustment. The rock drills feature swivel air inlets, four-pawl construction for positive rotation and automatic oilers.
Circle 160 on Reply Card ▪ freeproductinfo.net/rer